Well, I thought I would start a build on my Model Shipways Bluenose. Hopefully I will garner your help and others may benefit from my mistakes. I"m using Bob Hunts practicum. This is my first POB.
Right off the bat I found that the slots for the bulkheads on the stern part of the kit supplied center keel were set 1/16" too far toward the stern. I learned to always compare with plans. I cut new slots. I ordered a new center keel from Model-Expo and received it within a week. Don't think I will need it, so will have available if someone else does. I then glued all together and cut the rabbet joint (which was not as difficult as I thought it would be).
I learned from the "Shipmodeling for Dummies" site that Harold glued braces between each bulkhead which I found was a great stabilizer when fairing the hull.
I stole an idea from fellow forum member Steve (SSBN629) and added 1/8"x1/8" blocks to each side of bulkhead as a base to glue waterway filler planks later on.
Steve told me "READ AHEAD". I think Steve ran his between bulkheads. I also found that these blocks provided a way to clamp the waterway planks instead of using nails. I hope this works.
Next is Chapter 2 = Planking the Hull
http://shipmodeling.net/photopost/data/500/thumbs/000_0467.JPG (http://shipmodeling.net/photopost/data/500/000_0467.JPG)

Dennis:
The idea of "reading ahead" is a good one. Sometimes the kit instructions tell you to place a piece somewhere and if you do it's in your way later.

I don't think you are going to have any major problems with your first POB; it's just a different way to build a model. With your past success and experience you will do fine.

Looking forward to following your progress.

Dennis,
A quick note;
I too had some issues with the bulkheads, (The center slot was not on center at bulkhead "C").
From your picture I noticed that the "Ears" on the bulkheads, (Stantions), have not been brought to 1/8" x 1/8." Are you going to wait until after the hull planking? do it carefully as it will effect the look of the stantions when they are finished.
I'm 563 hours into my Bluenose and finished painting the hull, started making and adding hardware and am into building the Wheel box and Cabin.
Good Luck! and don't hesitate to inquire if you have any questions. This is my first build so I am no expert but have experienced th Bluenose kit build to the extent of 563 hours.

Bob

Hi Bob,
Nice to know you are building the Bluenose also. Now I can bug you for help. I have "not" cut the stantions to 1/8". Should I now to prevent a hassle later on? Your photos look great. Expect to hear from me. I'm new at this POB stuff.

Hi Dennis and Bob,

As I mentioned on the Scuttlebutt Forum Dennis I just finished my MS Bluenose. And Bob, I remember how long it seemed to get to the point you are then all of a sudden it just took off. Every new task seemed to make Bluenose look better and better. Are you including the fishing gear?

Dennis, I just cut my rabbet on the Constitution (and of course Bluenose), and like you I didn't find it as difficult as I thought it was going to be either. The bow and stern blocks seem to take be more difficult than I thought...or at least take longer than expected.

Do you guys work mostly by hand tools or by electical tools?

Tom

Hey Dennis,
Check this out:
http://modelshipworld.com/phpBB2/viewtopic.php?t=4954

Well, I finally finished planking the hull. Spent couple of days (on & off) sanding and wood putty filling. Now I know why you all preach about spending the extra time and effort fairing the hull. The Bluenose has a gentle flow to the hull thus makes planking easier for the first POB. I still have soaking/steaming/bending to look forward too. This was my first time using CA glue exclusively. Used medium viscosity with tip extender. Went very well. Next up is planking the deck. Any tips?
p.s. Thanks Ben for the MSW Bluenose site.
p.s. Tom, I use only hand tools. Only electrical tool I have is a Dremmel
which I sometimes use on solid hull.

Wow, that was fast. You did an awesome job. The photo isn't very close up, but from this viewpoint, it almost looks like a solid hull! No gaps anywhere. Great job!

Now that you have planked a hull, what do you think?

My camera is a cheap one, thus close ups get kinda fuzzy. Since hull will be painted, I feel that a solid hull is easier to shape. If I ever do a POB where hull will be stained then I think the time and effort will be worth it. But this a has been a great learning experience.

You did a great job planking the hull, Dennis. Congratulations on a job well done.
Joe

Finally finished the Bluenose decking. Next up, will run a couple of walnut strips along the bulwarks and install white false frame timbers.http://shipmodeling.net/photopost/data/500/thumbs/000_0499.JPG (http://shipmodeling.net/photopost/data/500/000_0499.JPG)http://shipmodeling.net/photopost/data/500/thumbs/000_0498.JPG (http://shipmodeling.net/photopost/data/500/000_0498.JPG)

Beautiful work, Dennis. What color stain?
Joe

Need some paint advice. Is there a difference between primer and flat white paint? Want to prime/paint Bluenose hull with a base coat of white so that I can have a white base for the hull stripe. I think it will also show me where I need additional sanding/filling. Your opinions will, as usual, be appreciated.

Hi Dennis -
I would suggest Winsor-Newton brand "GALERIA" acrylic paint applied directly from the tube . Easily obtained from most art supply/ craft stores . Excellent paint for wooden ship models .


HOLD FAST !

I got a can of spray white primer from Home Depot. After sanding and spraying a second coat it provided a nice base for the hull stripe. This method was recommended by the Lauck Street praticum and worked nicely for me.

Well, between cutting the grass, Honey-Do projects and lounging in the pool with a rum & coke I managed to finish the Bluenose cabin.http://shipmodeling.net/photopost/data/500/thumbs/000_0539.JPG (http://shipmodeling.net/photopost/data/500/000_0539.JPG)http://shipmodeling.net/photopost/data/500/thumbs/000_0532.JPG (http://shipmodeling.net/photopost/data/500/000_0532.JPG)

Hi Dennis -- cabin looks good - nice job!

by the by , do you take your duckies in the pool with you ? lol


HOLD FAST !

Very nice job, Dennis. Looks great. Rum and coke sound wonderful. Captain Morgan for me, please!
Joe

Dennis:
Nice work. Never mind the pool; Did you give your duckies some of the rum?

Dennis,
Been a way for a while, and just getting caught up.
Great job on the cabin.

Thanks for the kind words Ben,
Been wandering where you've been. Nice to have you back. Kip has been asking about you at SMW forum also. How's the Sultana coming?

Right now it's not coming. Put on the back burner. I'm travelling a lot for work (currently in a very hot Vegas for the week). And we're also getting ready to sell the condo and move to a bigger place. We found out a few weeks ago that we have a new addition to the family coming (our first) so we're looking for a house with a yard. So for now Sultana's going to have to wait.
I hadn't even had time in the last few weeks to follow along with my favorite forum threads, so I've been really jonesin' for a modeling fix.

Hi Ben --

"I've been really jonesin' for a modeling fix"

Interesting -- I have never heard that expression before - " jonesin' for a modeling fix"... -- where dies it come from , is is American slang ?


HOLD FAST !

I don't know if they're specific to US slang or not, but they're associated with addictions (often drugs).
To jones is to crave something, and a fix is what satisfies your addiction craving. Surprisingly, both are in Miriam Webster...www.m-w.com

Dennis,
I have finally gotten around to reading this forum thread.
I thought you you said you were going to build a POB and you are!
It is looking mighty fine.
I always look at that ship in the catalogue and think about buying one.
How do you feel about POB's now? Will you go back to solid hulls?

Keep up the good work.

Saturn V :coffee: