Photographing your Model
Note: If you hold your cursor over words highlighted like this, macro focus, a
small window will appear with a brief description or a link.
If you could make your models at a scale of 1:1 you wouldn’t need to be reading
this. Because models are a small representation of a large object they become a
challenge to photograph in a lifelike and pleasing manner. The object of this
article is to make it easier for you to produce photographs that do justice to
the models you make.
In a previous life I was a professional portrait and wedding photographer. While
my experience with commercial product photography is limited I have done enough
to be able to give some tips that may help your own photography.
The photography I see in the galleries is first rate. The biggest problem with
photographing anything as small as our models is the limited zone of focus and
sometimes backgrounds that are too cluttered to show off our work to its best
advantage
The basic principle of photography is to record an image on film or digital
sensors using light and lenses. The main thrust of this article will be on how
to use light, lenses, and backgrounds to your best advantage. I will try to take
in to account that most of us use point and shoot cameras and have little
control over the settings. I will assume that if you use a digital camera it has
some way to focus close, called macro focus, in the business.
Depth of field does not refer to the amount of water on the football pitch.
Depth of field is the zone of acceptable focus in your pictures and is based on
the focal length of your lens and the f/stop it is set at. Don’t worry if you
don’t know an F/stop from a shortstop, I will explain all as we progress. We
have all seen pictures where the foreground and background were out of focus
with a narrow strip of focus in the middle. This area is referred to as the
depth of field or the zone of acceptable focus. In a landscape of the rocky
mountains the zone of focus is still there it is just not very noticeable. In a
shot of a cannon at 1:64 scale it is a critical factor. The zone changes as the
focus of the lens changes becoming smaller as the camera is focused closer, it
also changes with the size of the lens opening that lets the light though. The
closer the focus and the larger the lens opening (f/stop) the narrower the zone
of focus. In the perversity of photo jargon the larger the f/stop number, the
smaller the opening. A small lens opening f:16 for example, gives you a bigger
zone of focus than one of larger opening like f:4. At the same time a small lens
opening lets through less light making a dark picture. We will discuss exposure
in more detail later in this article.
More light equals more focus
From the foregoing you will see that increasing the light on your subject will
allow a smaller lens opening and therefore an increase in the zone of focus. The
problem with light from a flash unit is that it decreases rapidly from its
source. An object that is two feet from your flash will receive one quarter the
light as an object only one foot away. (For the geeks among us that is the
inverse square law.) One of the tricks in commercial photography is to use
multiple light sources. A practical way for us, is to go outside and use
sunlight. Every part of your model is 93 million miles from the light source so
every part receives the same amount of light. The light is also bright enough to
allow the use of a small lens opening. The disadvantage of sunlight is the
presence of harsh shadows. This can be minimized by the use of fill flash from
your camera. Using a white reflector on the shadow side will also help eliminate
shadows. The smaller the light source the harsher the shadows. In this case the
sun is a pin point light source and so is your on-camera flash. A diffuser on
your flash can sometimes soften shadows to an acceptable level. A layer or two
of cheesecloth between the sun and your model will also do wonders for the
shadows.
Exposure
There is a definite quantity of light that will create a properly exposed photo,
one that is neither too dark or too light. The amount of light hitting your film
is determined by the size of the lens opening and the length of time it is open.
Time is measured in fractions of a second as in 1/60th or 1/100th of a second
and is controlled by the cameras shutter. For the same exposure, a large lens
opening requires a shorter time interval and a small lens opening requires a
longer time. In a low light situation to get an adequately exposed photo you
will need a large lens opening and a long shutter time. The large lens opening
reduces the zone of focus and a long shutter time increases the chance of camera
shake also reducing the sharpness of your image. A tripod will reduce camera
shake but is not always practical to use. Film with a high ASA rating will allow
greater flexibility and setting your digital to a higher ASA will do the same
for it. The higher the ASA rating, the greater the sensitivity to light allowing
smaller lens openings.
From all of the foregoing you will see that one of the keys to good pictures of
your models is the quality and quantity of light. Multiple flashes or high power
studio lights is the way the pros do it. In our case, sunlight or even window
light combined with on camera flash is about the best we can get. If you have an
adjustable camera you have the option of setting your f/stop for a large depth
of field and controlling the exposure with the shutter, taking care to prevent
camera shake.
Camera shake is probably the leading cause of less than razor sharp photos. It
is almost impossible to hold a camera steady at a shutter speed of less than
1/60 of a second and I am sorry to say as we age it becomes even harder. A
tripod is an obvious remedy but is not always easy to set up or to maneuver
around the intricacies of our models. Sometimes a tabletop tripod or even a
short monopod will get the sharpness we need. There seems to be some inherent
unsharpness in digital images. I have never taken a photo or scanned an image
that didn’t benefit from sharpening in whatever image software I was using. Raw
digital images will usually also benefit from some tweaking in the contrast
and/or brightness settings. One of the problems unique to our situation is that
you can never know what kind of monitor our images will be seen on. I have done
some work in a telephone call center. A row of monitors essentially showing the
same image will be all different tints and even show different degrees of
sharpness. In the end the only people who need to be happy with our photography
is us, if it looks good on your monitor it will be acceptable on most others.
Backgrounds
With a subject as complex as our ship models the backgrounds in out photos need
to be as simple as possible. Too much clutter makes it difficult to see the
details of masts and rigging. Something as simple as hanging a sheet on the wall
or placing a large sheet of poster paper behind your masterpiece will make it
stand out. One of the basic concepts of art and photography is that light
objects attract the eye. A dark background will tend to recede as it should and
focus the eye on the subject. A dark background slightly out of focus is ideal.
One of my most popular backgrounds was a dark storm cloud scene, I wish I still
had it, it would be perfect for model photos. Showing your workbench with all
its clutter (at least mine is) is perfectly acceptable, but for the finished
model find a nice dark simple background (and use plenty of light).
Feel free to post a comment with any questions, or even flames.
Michael AKA Trawlerman